| |

iFix 爱修网

 Forgot password?
 Register

QQ登录

只需一步,快速开始

iFix爱修网知识星球,等待你的加入。。。
Author: admin

RT809F编程器—仁宝代工笔记本EC在线读写_KB9012_9010_9016_KB9022_联想_华硕_宏基_HP

  [Copy link]
Post time: 2014-11-28 16:52:55
| Show all posts
今天遇到E430不触发,拆板量无3,5v电压,刷KB9012 显示OK,多谢老师分享
Reply Support Not support

Use magic Report

Post time: 2014-12-9 21:43:08
| Show all posts
拆下来刷还不容易出错
Reply Support Not support

Use magic Report

Post time: 2015-6-22 15:36:16
| Show all posts
飞线到隐秘的针脚那,难度有点大,麻烦

Comments

飞线,与拆焊,谁麻烦,相信不用我说吧。  Post time 2015-10-16 12:51
Reply Support Not support

Use magic Report

Post time: 2015-10-11 14:48:41
| Show all posts
季总伟大,坚决支持。
Reply Support Not support

Use magic Report

Post time: 2015-10-31 12:56:39
| Show all posts
我想刷KB9022Q, 但是焊到转接板上编程器认不了,一直显示“引导错误,请检查EC是否上电、ISP线与EC是否接好,ISP线长度不要超过10厘米。”
怎么办?
Reply Support Not support

Use magic Report

 Author| Post time: 2015-11-1 16:52:15
| Show all posts
nsxt99 发表于 2015-10-31 12:56
我想刷KB9022Q, 但是焊到转接板上编程器认不了,一直显示“引导错误,请检查EC是否上电、ISP线与EC是否接 ...

只要芯片是好的并且焊接好了,肯定是可以识别和读写的。
Reply Support Not support

Use magic Report

Post time: 2015-11-2 16:27:29
| Show all posts
admin 发表于 2015-11-1 16:52
只要芯片是好的并且焊接好了,肯定是可以识别和读写的。

芯片是新的。
焊了个KB9012就能够读写,唯独KB9022不行。
Reply Support Not support

Use magic Report

 Author| Post time: 2015-11-2 19:39:03
| Show all posts
nsxt99 发表于 2015-11-2 16:27
芯片是新的。
焊了个KB9012就能够读写,唯独KB9022不行。

在原板子上面飞线试试看。
Reply Support Not support

Use magic Report

Post time: 2015-11-26 17:50:21
| Show all posts
admin 发表于 2015-11-2 19:39
在原板子上面飞线试试看。

我也遇到同样情形kb9022無法辨識,kb9012跟kb9022烧录脚位确定一样吗?
錯誤訊息:
"111:  引脚接触良好。
112:  ID识别错误,芯片没放好或者已经损坏。"
连续换2颗kb9022都一样,
Reply Support Not support

Use magic Report

 Author| Post time: 2015-11-27 08:47:35
| Show all posts
faijiang 发表于 2015-11-26 17:50
我也遇到同样情形kb9022無法辨識,kb9012跟kb9022烧录脚位确定一样吗?
錯誤訊息:
"111:  引脚接触良好 ...

请提供一份使用KB9022芯片的笔记本主板图纸,我们分析看看,谢谢。
Reply Support Not support

Use magic Report

You have to log in before you can reply Login | Register

Points Rules

QQ|||iFix 爱修网 ( 粤ICP备2021135374号 )

粤公网安备 44060602002064号

2021-10-28 01:24 GMT+8 , Processed in 0.089825 sec., 15 queries .

Powered by Discuz! X3.4

Release 20191201, © 2001-2021 Comsenz Inc.

MultiLingual version, Rev. 850, © 2009-2021 codersclub.org

Quick Reply To Top Return to the list